Norcold Power/ Circuit Board 628661 | New Style
This is the current Norcold power board being used in most Norcold refrigerators manufactured after 2006 and prior to 2019ish. Make sure that you see your Norcold model listed below before ordering. Your model number tag can be located inside the refrigerator on the right hand side.
This Norcold circuit board is the gateway for voltage getting to the various components of the refrigerator.
Below are the Norcold refrigerator models that this board fits: (If your refrigerator was manufactured in 2006 or newer, this could be the board that you need. Simply put, if your power board looks like the one above, then it is the one above because no other Norcold power board looks like this. If your refrigerator was manufactured Pre-2006, then this board will not fit your refrigerator, regardless of model number.)
N41X/ N51X Series- N410, N410.3, N412, N412.3, N510, N510.3, N512, N512.3
N6XX Series - N611, N621, N621F, N623, N624, N641, N641F, N643
N8XX Series - N811, N821, N821F, N821V, N822, N822F, N823, N824, N841, N841V, N842, N843
NX/ NXA Series - NX611, NX641, NX641.3, NXA641, NXA641.3, NX811, NX841, NX841.3, NXA841, NXA841.3
N1095 Series
1200 Series
1210 Series
1211 Series
2117 Series
*if your model ends in a "3" or .3", it means that it has a DC heating element. If you need the DC board for that heater, you can find it at the link below:
Norcold 3 way DC Board <-click
Serial Number range will vary with the specific model refrigerator, however, if the board you have on your refrigerator looks like the board pictured above, IT IS! This style board has two plug connectors (one row of 10 pins and one row of 6 pins) while the older style boards are more rectangular and have only one 16 pin plug connector.
Troubleshooting
Potential problems that a new power board could solve:
- Refrigerator not sensing AC power
- Refrigerator not sensing AC heating element
- Refrigerator not sensing a flame
- Refrigerator not powering on
- Refrigerator incapable of resetting
- Intermittent issues
- SR code display
- If any electrical burn marks are present anywhere on front or back of power board, you should replace it.
Installation
Time: 30 minutes or less
Tools:
- Ratchet set
- Screwdriver
Steps:
- Turn your battery switch to OFF
- Remove power board cover
- Take a picture of the board before disconnecting any wires
- Disconnect all wires and remove defective board
- Place new board on old board cover base and connect wires
- Before placing board cover on, turn battery switch ON and power up refrigerator to verify everything is connected and that there are no faults present. If everything is working, put cover back on.
46 Reviews
-
defective board
Had an SR code on 1200LRIM Norcold. Tried hooking up independent power source like your article said and the code remained. Replaced board and it's now working great.
-
not working on propane
My unit would spark and ignite on propane but once the sparking stopped the flame went out. This was enough information for the Norcold Guy to determine I had a bad board. They were right! Part was received in 2 days even though I ordered it ground shipping for $5. Very happy abou the whole experience
-
Easy install
Pulled loose old wires and plugged in the new board. Replaced wires and it's running normal.
-
Good part but missing a wire jumper
Part came quickly and was packaged well. The only negative is that although all of the fuses were installed, it did not come with the jumper wire for the Limit In and Limit Out terminals installed. It took some time to figure out why the board was not working properly with all the cables from the fridge connected. Luckily I had saved the old board and was able to salvage the jumper cable from it.
-
excellent service
The board was an exact replacement and took all of ten minutes to replace the old board. I am especially appreciative of the fast service. I paid for three day ground service but had the board the next day. Excellent! Hint: any time you replace something with wires, make a quick sketch first.
